SKU KCS-COAX-RG59-POWER

RG59 Coaxial Cable with Power for CCTV

KSh 40 per metre
In stock — pick up today in Nairobi CBD

RG59 coaxial cable with power combines a video coax and power conductors in one sheath, so a single cable run carries the picture back to the DVR and DC power out to the camera. It suits analogue and HD-over-coax CCTV systems in homes, shops and compounds in Kenya.

  • Coax video and power conductors in one cable
  • For analogue and HD-over-coax CCTV cameras
  • One pull per camera instead of two
  • Works with DVR-based camera systems
How our CCTV installation works, and what it costs ↗

Frequently bought together

Complete your setup in one go
Total for 4 items KSh 6,790
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

This RG59 cable with power is the two-in-one cable used for coax CCTV cameras. The RG59 coaxial part carries the video signal from the camera back to the DVR, and the power conductors alongside it carry DC power out to the camera. Each camera then needs one cable pull instead of two, which saves time on ladders and in ceilings.

What it is used for

RG59 is the coax size most often used for CCTV video. Analogue cameras and HD-over-coax cameras (HD-TVI, HD-CVI and AHD) send their picture along it to a DVR. At the camera end the coax takes a BNC connector and the power conductors are joined to the camera's DC lead. At the recorder end the coax goes to the DVR and the power conductors go to a CCTV power supply or power distribution box.

  • Wiring DVR-based CCTV systems in homes and shops
  • Replacing a damaged camera cable on an existing coax system
  • Runs where pulling a separate power cable would be awkward

Planning your cable runs

Measure each run along the route the cable will really take, around corners, up walls and through ceilings, and add a little extra for a service loop at each end. On longer runs the power side usually sets the limit: low-voltage DC loses some voltage along thin conductors, so a camera at the far end of a long run gets less than the supply puts out. For long runs, place the power supply closer to the cameras or use a supply with an adjustable output, and measure the voltage at the camera end before you finish.

Installation tips

  • Run the cable in conduit or trunking outdoors and along walls, to protect it from sun and knocks.
  • Keep it apart from mains cables where you can, to reduce interference on the picture.
  • Fit BNC connectors to the coax at both ends, and connect the power conductors with the correct polarity.
  • Test every camera before you clip the cable in place and close up ceilings.

What you need with it

  • BNC connectors for both ends of each coax run
  • DC power connectors and a CCTV power supply or distribution box
  • Cable clips, conduit or trunking
  • A DVR that supports your cameras' video format

Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the cable in stock, including how it is sold. Collect it from the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or have it delivered within Nairobi (up to 45 km) or by courier across Kenya in 1 to 3 working days.

Frequently asked questions

Can I use RG59 cable with power for HD cameras?

Yes. HD-over-coax cameras, sold as HD-TVI, HD-CVI or AHD, are made to run on coax such as RG59 and connect to a DVR. How far you can run depends on the camera format and the cable quality, so check the maximum coax distance given in your camera or DVR manual before planning very long runs.

How do I power the camera through this cable?

Connect the power conductors at the recorder end to a CCTV power supply or a power distribution box, and at the camera end to a DC plug that fits the camera lead. Keep positive and negative the right way round, and check the voltage at the camera end on long runs.

What connectors do I need?

Each coax run needs a BNC connector at both ends, one for the camera and one for the DVR. The power conductors need a DC connector at the camera end, usually a male DC plug, and a connection to the supply at the other end. Have a stripping tool ready so the coax is cut cleanly.

Can I use it for IP cameras?

No. IP cameras use network cable such as Cat5e or Cat6 and connect to an NVR or PoE switch. RG59 cable with power is for coax cameras connected to a DVR. If you are upgrading an old coax system to IP, plan new network cabling for the IP cameras.

KSh 40 In stock