SKU KCS-RJ45-CAT6

RJ45 Cat6 Connectors

KSh 1,000 per box
In stock — pick up today in Nairobi CBD

RJ45 Cat6 connectors are the plastic plugs fitted to the ends of Cat6 network cable. They suit IP camera runs, NVR and switch links and office patch leads across Kenya. Crimp one onto each end of a cable, then plug it into a camera, router, switch or wall socket.

  • RJ45 plug for Cat6 network cable
  • Eight-contact Ethernet connector
  • For IP cameras, NVRs, switches and routers
  • Crimp on to cut-to-length cable
How our CCTV installation works, and what it costs ↗

Frequently bought together

Complete your setup in one go
Total for 3 items KSh 8,000
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

These RJ45 Cat6 connectors are the small clear plugs that go on the ends of a Cat6 network cable so it can plug into a camera, recorder, switch, router or wall socket. If you pull your own cable in Nairobi or anywhere else in Kenya, you need two connectors for every cable run.

Key features

  • RJ45 plug with eight contacts, the standard connector for Ethernet cable.
  • Marked for Cat6 cable, the grade normally used for modern IP camera and network installations.
  • Fitted with a crimping tool, so a cable can be cut to the exact length you need.

Where to use them

IP CCTV systems depend on network cable, and every camera cable ends in an RJ45 plug at the camera side and at the NVR or PoE switch side. The same connector is used for patch leads between a router and a switch, for access points, and for office desks.

Terminating your own cable is useful when a run has to pass through a conduit or a small hole, because you can pull the bare cable through first and fit the plug afterwards. It also lets you make a lead of the exact length instead of coiling spare cable behind a rack.

How to fit one

  • Strip the outer jacket back by about the length of the plug body.
  • Untwist the pairs only as far as needed and arrange the eight wires in the colour order of your chosen standard, T568A or T568B, using the same standard on both ends.
  • Trim the wires level, slide them fully into the plug until they reach the end, and crimp with an RJ45 crimping tool.
  • Test the finished cable with a cable tester before you connect equipment.

What to buy with them

You will need Cat6 cable, an RJ45 crimping tool with a stripper, and a cable tester. Connector boots slip over the plug to protect the latch, and a coupler lets you join two finished cables. Kefa Solutions technicians can install CCTV cameras if you would rather have the cabling done for you.

Cat6 plugs work best with Cat6 cable. Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock.

Frequently asked questions

How many RJ45 connectors do I need per cable?

You need two for each cable run, one at each end. If you are wiring four IP cameras, that is eight connectors plus a few spares, because it is common to spoil a plug while learning to crimp. Always use the same wiring standard, T568A or T568B, on both ends of a cable.

Can I use these on Cat5e cable?

Cat6 plugs are made for Cat6 cable. Cat6 conductors are usually a little thicker than Cat5e, so a plug sized for one may not seat perfectly on the other. For the best result, match the plug to the cable category you are using, and ask our team if you are unsure.

What tools do I need to fit them?

You need an RJ45 crimping tool, ideally one with a built-in cable stripper and cutter, and a cable tester to check the finished lead. A pair of side cutters helps to trim the wires evenly. Without a proper crimper, the contacts will not bite into the wires and the connection will be unreliable.

KSh 1,000 In stock