SKU KCS-CRIMPING-TOOL

Crimping Tool

KSh 1,300
In stock — pick up today in Nairobi CBD

A crimping tool presses a plug onto the end of a cable so that it makes a firm, lasting connection. In CCTV and network work in Kenya it is used mainly to fit plugs on network cable for IP cameras, recorders, routers and access points, and it belongs in every installer's toolbag next to a cable tester.

  • Fits plugs firmly to network cable
  • Used for IP camera, NVR and router cabling
  • Lets you make patch leads to exact length
  • Pair it with a cable tester to check every lead
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

A crimping tool is the tool that turns a cut cable into a working lead. You place the plug, with the wires inside it, into the shaped slot of the tool and squeeze. The tool pushes the plug's metal contacts down through the insulation of each wire and clamps the plug onto the cable jacket, so the connection stays put when the cable is pulled or moved.

Where installers use it

On CCTV and network jobs across Nairobi and the rest of Kenya, the crimper is used for:

  • Terminating network cable for IP cameras and NVRs.
  • Making patch leads to the exact length a cabinet needs.
  • Re-terminating a damaged plug instead of replacing a whole run.
  • Fitting plugs on cable for routers, access points and computers.

How to crimp a network plug

  • Strip about 2 to 3 cm of the outer jacket without nicking the wires inside.
  • Untwist the pairs and lay the wires flat in the colour order you have chosen. Many installers use T568B: white-orange, orange, white-green, blue, white-blue, green, white-brown, brown.
  • Trim the wires straight across, leaving them just long enough to reach the end of the plug with the jacket inside the plug.
  • Push the wires in until each one touches the front of the plug.
  • Put the plug in the matching slot of the tool and squeeze firmly, all the way.
  • Fit the other end in the same order, then check the lead with a cable tester.

Common mistakes

Most failed crimps come from three things: a wire that stopped short of the contact, the colour order changing between the two ends, or the jacket sitting outside the plug so the wires take the strain. Look through the side of the plug before you squeeze, and you will catch all three.

Choosing plugs to go with it

Use plugs that match your cable. Cat6 cable has thicker conductors than Cat5e and is easier to terminate with plugs made for it. Pass-through plugs, where the wires come out of the front of the plug, need a tool with a blade that trims them flush. Plug boots protect the clip and give a neater finish.

What you need with it

  • Network plugs to suit your cable, plus boots.
  • A cable tester to check each lead.
  • A cable stripper if the tool has no stripping slot.

Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock, including the plug sizes it crimps.

Frequently asked questions

Can one crimping tool handle both Cat5e and Cat6 plugs?

The crimping slot for network plugs is the same shape for Cat5e and Cat6, so one tool usually works with both. What changes is the plug: use plugs made for the cable you are terminating, because Cat6 wires are thicker. Pass-through plugs are the exception, as they need a tool with a blade that cuts the wires flush.

Which colour order should I use?

Use the same order at both ends of the cable. Many installers in Kenya use the T568B order: white-orange, orange, white-green, blue, white-blue, green, white-brown, brown. T568A also works if both ends match. Mixing the two on one cable creates a crossover, which modern equipment usually copes with, but it makes fault-finding confusing later.

Why does my newly crimped cable fail the tester?

Usually one wire did not reach the front of the plug, two wires swapped places while being pushed in, or the tool was not squeezed fully. Cut off the plug, re-trim the wires straight, check the order through the side of the new plug and crimp again with one firm, complete squeeze. Then repeat the test.

What plugs should I buy with a crimping tool?

Buy plugs that suit both the cable and the job: Cat6 plugs for Cat6 cable, Cat5e plugs for Cat5e cable, and shielded plugs if you use shielded cable. Add plug boots for leads that will be handled often. Buy extra, because a few plugs are always lost to practice and to re-terminations on site.

KSh 1,300 In stock