
Cable Tester
A cable tester checks that a cable is wired correctly from one end to the other, showing broken, shorted or crossed wires before you blame the camera or switch. It is a basic tool for CCTV and network installers in Kenya, used after fitting plugs and when a device on a long run stops responding.
- Shows broken, shorted and crossed wires in a cable
- Check every run straight after crimping plugs
- Test installed runs from patch panel to wall socket
- Rules out the cable before you change device settings
- Pickup from 3 Nairobi branches
- Nairobi delivery from KSh 200 (KSh 50/km)
- Countrywide courier in 1–3 working days
- Pay by M-Pesa, cash or bank transfer
Overview
A cable tester tells you, in a few seconds, whether a cable you have just terminated is wired properly. On a CCTV or network job that saves a lot of guesswork: when an IP camera will not come online, the first question is whether the cable is good, and the tester answers it before you start changing settings or swapping equipment.
What it checks
The common type used by installers has a main unit and a small remote unit. You plug one end of the cable into each, and the tester steps through the wires one at a time. On a straight-through network cable each wire should show up in the same position at both ends, 1 to 1 through to 8 to 8. If a position is missing, doubled or out of order, you know where to look.
- Open wire: a conductor is broken or did not reach the end of the plug.
- Short: two wires are touching.
- Crossed wires: the colour order differs between the two ends.
When to use it
- Straight after crimping new plugs, before closing trunking or ceiling boards.
- When reusing old cable left behind by a previous installer.
- When a camera, access point or computer on a long run drops off the network.
- To check patch leads before you hand over a finished job.
Testing a cable that is already installed
Unplug the run from switches, recorders, cameras and PoE injectors first; testers are meant for unpowered cables. Then connect the main unit at the patch panel or recorder end with a short known-good patch lead, and the remote unit at the wall socket or camera end with another. Run the test and compare the result with the expected order. If a fault shows, re-terminate the end you suspect and test again.
What a pass does and does not mean
A basic tester proves that every wire connects to the right place. It does not measure how fast the cable can carry data. A run that passes can still give trouble if it is longer than 100 metres, if too much of the twist was undone at the plug, or if the cable itself is poor. Use good cable and neat terminations as well as the tester.
What you need with it
- A crimping tool and spare plugs for re-terminating faults.
- Two short patch leads for testing installed runs.
- A cable tracer if the runs are not labelled.
Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock, including which plugs it accepts. Collect from our shop in Nairobi CBD or order for delivery across Kenya.
Frequently asked questions
My cable passes the test but the IP camera still does not work. Why?
A wiring pass rules out the most common fault, but not all of them. Check that the run is under 100 metres, that the PoE switch or injector has enough power for the camera, and that the camera's IP address suits your network. Poor quality cable or untwisted pairs at the plug can also cause drop-outs even when the wiring order is right.
Can I test a cable that is already fixed in the wall?
Yes. Disconnect it at both ends, then use a short patch lead to connect the main unit at the patch panel or recorder end and another patch lead to connect the remote unit at the wall socket or camera end. The tester then checks the whole run, including the sockets, without you pulling any cable out.
Do I need to unplug the cable from the switch before testing?
Yes. Cable testers are made for cables with no power or data on them. Testing a run that is still plugged into a switch, router or PoE injector can give false results and may damage the tester. Unplug both ends, run the test, then reconnect the equipment once the cable passes.
What does a crossed wire result mean?
It means the wires are in a different order at one end compared with the other, usually because the colour sequence was not followed when the plug was fitted. Cut off the faulty plug, straighten and re-order the wires to the same standard used at the other end, crimp a new plug and test again.