Fibre Splitter 1x4
A 1x4 fibre splitter divides one fibre feed into four outputs. It suits small clusters of users, such as four houses in a court, four shops in a row or a small apartment block, and is a common building block in FTTH and PON networks across Kenya.
- Shares one fibre feed between four outputs
- Passive: no power or setup
- Suits small clusters of users
- Common branch splitter in cascades
- Pickup from 3 Nairobi branches
- Nairobi delivery from KSh 200 (KSh 50/km)
- Countrywide courier in 1–3 working days
- Pay by M-Pesa, cash or bank transfer
Overview
A fibre splitter 1x4 shares the light from one incoming fibre between four outputs. Like all PON splitters it is passive, so it needs no power and has nothing to set up. It sits in a closure or distribution box and turns one feeder fibre into four drops.
Where a 1x4 split fits
Four outputs is a practical size for small groups of users close together:
- A court of four houses in an estate
- A short row of shops or offices in one building
- A small apartment block with a few units per floor
- A branch of a cascade, after a first-stage splitter in a street cabinet
In Nairobi estates, a common pattern is a splitter in the street feeding smaller splitters near each group of houses. A 1x4 at the end of a branch keeps drop cables short, which makes them neater and easier to repair.
Signal budget
Dividing light four ways cuts it to a quarter, which in theory is a loss of about 6 dB, and real splitters lose a little more. That is more than a 1x2 and less than a 1x8. Before adding a splitter, add up the losses along the route: the splitter, the fibre length, every splice and every connector. The total must stay within what the OLT and ONUs can handle, so customers at the far end still get a strong signal.
Installation and setup
- Mount the splitter in a protected closure or distribution box.
- Connect the input to the feeder fibre and each output to a drop cable.
- Coil fibre loosely, without tight bends, and secure the splitter body.
- Measure the signal at each output with a power meter before connecting customers.
- Label every output with the house or unit it serves.
Not for point-to-point links
Splitters belong in PON networks with an OLT and ONUs. For a simple fibre link between two buildings on a CCTV job, use a pair of media converters instead.
What you need with it
- A distribution box or closure
- Pigtails, fast connectors or splicing equipment
- Drop cables and ATBs for each user
Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock. Collect it from the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or have it delivered within Nairobi (up to 45 km) or by courier across Kenya in 1 to 3 working days.
Frequently asked questions
How many users can a 1x4 fibre splitter serve?
Four outputs means up to four users or four branches from one feed. In a cascade, each output can feed another splitter, so a 1x4 followed by four 1x8 splitters gives thirty-two outputs. The OLT and ONU equipment must support that many users and the signal budget must allow for both splitters.
Should I use one 1x4 or two 1x2 splitters?
A single 1x4 is simpler, takes less space and has fewer splices. Two 1x2 splitters cascaded behind a third would give the same count but add joints and loss. Use cascades when users are spread out and you want the final split close to each group.
How do I know the signal is good enough after splitting?
Measure each output with an optical power meter, then check the level at the ONU once connected. The reading must be inside the range the ONU accepts. If it is too low, look for dirty connectors, tight bends or extra splices before blaming the splitter.