SKU KCS-POE-INJECTOR-24V

24V 1A PoE Injector

KSh 1,500
In stock — pick up today in Nairobi CBD

A 24 V, 1 A PoE injector that adds DC power to a network cable so one cable carries both data and power to a device. It suits wireless bridges, outdoor CPE radios and other equipment made for 24 V PoE, which installers in Kenya often mount on masts and rooftops far from a socket.

  • 24 V 1 A power over the network cable
  • Passive 24 V type for 24 V PoE devices
  • Suits wireless bridges and outdoor radios
  • One cable carries both data and power
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

A 24v poe injector takes power from the mains and puts it onto an Ethernet cable together with the network data. The device at the far end, often a radio on a mast or roof, then needs only one cable, with no socket or separate adapter at the top.

24 V PoE is not standard PoE

This is the key point before buying. Standard PoE, used by most IP cameras and PoE switches, runs at around 48 V and only powers a device after a handshake that confirms it can accept power. A 24 V injector is the simpler passive type: the voltage is placed on the cable without a handshake. That suits equipment made for 24 V passive PoE, such as many outdoor wireless bridges, CPE radios and some access points, but it is not the right choice for a standard PoE IP camera.

  • 24 V output on the network cable, 1 A.
  • About 24 W available at the injector.
  • One cable for data and power.
  • For devices that state 24 V PoE on the label.

Where to use it

Typical uses are point-to-point wireless links between two buildings, for example a gate house and main house, an outdoor radio feeding internet to a rural home or a farm, or a 24 V access point in a ceiling. Wireless links like these are also a common way to bring CCTV footage back from a remote gate or outbuilding in Kenya.

Installation and setup

Plug the injector into the mains indoors. Connect a cable from your router or switch to the LAN or data port, and run the cable to the device from the PoE port. Keep the injector itself indoors or in a weatherproof box; only the network cable should go outside. Check port labels carefully, because swapping the two ports means the device receives no power. Never plug the PoE port directly into a laptop, router or other device that is not designed for 24 V PoE.

Long and thin cable reduces the voltage that reaches the device, so use good quality network cable on long runs.

What you need with it

  • Outdoor-rated network cable to the device.
  • RJ45 connectors and a crimping tool.
  • A surge protector for mast-mounted radios.

Collect from the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or order delivery within Nairobi or by courier across Kenya.

Frequently asked questions

Can I use a 24V PoE injector for an IP camera?

Only if the camera label says it accepts 24 V passive PoE, which is uncommon. Most IP cameras use standard PoE at around 48 V and may not start, or could be damaged, on 24 V passive power. For standard PoE cameras, use a PoE switch, a PoE NVR or a standard PoE injector.

Which port goes to the router and which to the device?

The injector has one port marked for data, often labelled LAN, and one marked for power and data, often labelled PoE. Connect the router or switch to the data port, and the cable going to the radio or access point to the PoE port. Swapping them leaves the device unpowered.

How far can a 24V PoE injector send power?

Ethernet data is designed for runs of up to 100 metres per cable. The power that arrives also depends on cable quality, conductor thickness and how much the device draws. Thin or poor cable loses more voltage. If the device restarts or will not link, shorten the run or use better cable.

KSh 1,500 In stock