
12V 2A Power Adapter JAS-1202
The JAS-1202 is a plug-in power adapter that gives 12 V DC at up to 2 A. It is the everyday way to power a single CCTV camera, a small DVR or NVR, or a 12 V router in Kenyan homes and shops, plugging straight into a wall socket with no wiring of mains terminals.
- 12 V DC output at up to 2 A
- Plugs straight into a wall socket
- Powers one camera, small recorder or router
- Easy replacement for a failed adapter
- Pickup from 3 Nairobi branches
- Nairobi delivery from KSh 200 (KSh 50/km)
- Countrywide courier in 1–3 working days
- Pay by M-Pesa, cash or bank transfer
Overview
The JAS-1202 is a 12v 2a power adapter: a plug-in unit that converts mains power into 12 V DC on a cable with a DC plug. You may hear it called a 12.2 adapter, short for 12 volts, 2 amps. It is the simplest way to power one device, because it plugs straight into a wall socket or extension and needs no mains wiring.
What it powers
Two amps at 12 V is about 24 W. That is enough for most single CCTV cameras, including their infrared lights at night, and for many small 4-channel and 8-channel recorders, home routers and other 12 V devices. Always check the label on the device: the voltage must say 12 V DC, and the current it asks for must be 2 A or less. A device that needs more than 2 A, such as some larger recorders, needs a bigger supply.
- 12 V DC output, up to 2 A.
- About 24 W.
- Plug-in design, no mains wiring.
- Model code JAS-1202.
Choosing between an adapter and a central supply
One adapter per camera keeps each camera independent: if one adapter fails, only that camera goes off, and replacing it is a quick swap. The trade-off is that you need a socket near each camera or a long DC cable back to an extension. For systems of four or more cameras installed in one go, a central supply or a CCTV power box in the cabinet is often tidier. Adapters remain ideal for adding one extra camera, replacing a failed adapter, or powering the recorder itself.
Installation and setup
Check that the DC plug fits your device before connecting. Many CCTV cameras use a round barrel connector with the centre pin positive, but sizes and polarity vary, so compare with the old adapter or the device label. Keep the adapter indoors or inside a weatherproof junction box, because adapters are not made to get wet. Where the cable to an outdoor camera is long, voltage drops along the way, so use proper power cable rather than thin speaker wire. Kefa Solutions technicians can install CCTV cameras.
What you need with it
- DC extension cable or power cable to the camera.
- A junction box for outdoor connections.
- A surge-protected extension for the recorder area.
Collect from the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or order delivery.
Frequently asked questions
Can I use a 12V 2A adapter on a device that asks for 12V 1A?
Yes. The voltage must match, but the current rating of the adapter only needs to be equal to or higher than what the device asks for. A 12 V 1 A camera will draw only what it needs from a 2 A adapter. The reverse is not safe: a 2 A device on a 1 A adapter can overheat it.
Will it power my DVR?
Many small 4-channel and 8-channel DVRs and NVRs run on 12 V DC at 2 A or less, and this adapter suits them. Larger recorders, especially those with several hard disks or built-in PoE, usually need more power. Check the input rating printed under the recorder before buying.
Can I power two cameras from one 12V 2A adapter?
It is possible with a DC splitter cable if both cameras together draw well under 2 A, including at night when infrared lights are on. For more than two cameras, a central power supply or CCTV power box is the safer choice, as it is designed to share power between several outputs.