SKU KCS-POE-SPLITTER-2WAY

2-Way Cabled PoE Splitter

KSh 300
In stock — pick up today in Nairobi CBD

A 2-way cabled PoE splitter is a lead-style adapter used to share one network cable between two devices, typically two IP cameras mounted close together. It saves pulling a second long cable on Kenyan installs where one run already reaches the area, at the cost of lower network speed per device.

  • Shares one cable run between two devices
  • Cabled Y-lead design, no box
  • Suits two IP cameras close together
  • Saves pulling a second long cable
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

A 2 way poe splitter of the cabled type is a short Y-shaped lead rather than a box. Splitters of this kind are used to let one long network cable serve two devices, most often two IP cameras that sit near each other at the far end of a run, such as both sides of a gate or two corners of the same wall.

How cable sharing works

A standard network cable has eight wires in four pairs. Ordinary 10/100 Mbps Ethernet only uses two of those pairs for data, which leaves two pairs unused. Cable-sharing splitters put one device on two pairs and the second device on the other two. They are normally used in pairs: one at the switch or NVR end to combine two ports onto the cable, and one at the camera end to separate them again.

  • Y-shaped cabled design, no box.
  • Two connections from one network cable run.
  • Typically used in pairs, one at each end.
  • Suits two cameras mounted close together.

Know the limits

Because each device only gets two pairs, it is limited to 10/100 Mbps, which is enough for most CCTV cameras but not for equipment that needs faster links. Power over Ethernet also has to travel on the pairs each device uses, so the cameras and the PoE switch or NVR must work with that arrangement. Check how your cameras take power before relying on this method. Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock and how it is wired.

Installation and setup

At the recorder end, plug the two legs into two ports on the PoE switch or NVR and the single end into the long cable. At the camera end, connect the single end to the cable and one camera to each leg. Keep the camera-end splitter inside a junction box so water cannot reach the connectors, and avoid bending the legs sharply at the plugs. Label which leg feeds which camera. Kefa Solutions technicians can install IP camera systems.

When to choose another option

If you need more than two cameras at the far end, speeds above 100 Mbps or extra distance, a PoE extender or a small outdoor PoE switch is usually the better approach.

Frequently asked questions

Can I run two IP cameras on one network cable?

Yes, with a pair of cable-sharing splitters, one at each end. Each camera uses half the cable's wire pairs, so each link runs at up to 100 Mbps, which most CCTV cameras handle comfortably. Both cameras and the PoE source must work with the split wiring for power to reach them.

Do I need one splitter or two?

Cable-sharing splitters are normally used as a pair. One combines two switch or NVR ports onto the single cable, and the other separates the two connections again at the cameras. Using only one end usually means one of the two cameras gets no connection. Check how the unit in stock is supplied when you buy.

Is a 2-way splitter better than a PoE extender?

They solve different problems. A 2-way splitter shares one cable between two devices but does not add distance. A PoE extender starts a new cable segment so you can go further, and some models have several outputs. If the cameras are beyond 100 metres, you need an extender.

KSh 300 In stock