SKU KCS-PSU-BOX-18CH-20A

18-Channel CCTV Power Supply 12V 20A

KSh 6,000
In stock — pick up today in Nairobi CBD

An 18-channel CCTV power supply that takes mains AC and delivers 12 V DC at 20 A in total, shared across 18 separate outputs. It is built for 16-camera systems and other large installations in Kenya, giving every camera its own output from one central unit beside the recorder.

  • 18 separate 12 V DC outputs
  • 20 A total output, about 240 W
  • Suits 16-camera systems with spare channels
  • Mains AC input
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

This 18 channel cctv power supply combines a 12 V DC, 20 A power source with 18 individual outputs, one for each camera. Instead of a large supply feeding a separately built distribution board, the outputs are ready to connect, which keeps a busy equipment cabinet neat and makes it easy to see which cable goes to which camera.

Why 18 outputs and 20 A

Eighteen channels match a 16-channel recorder with two outputs to spare, for example for a later camera or a small 12 V device. The 20 A is the total for all outputs together, not per channel. Shared evenly across all 18 outputs, that is a little over 1 A each, which is comfortable for most fixed cameras. Before connecting, add up the current rating of every camera, using the night-time figure with infrared or white lights on, and keep the total under 20 A with some margin.

  • Mains AC input, 12 V DC output.
  • 20 A total output current, about 240 W.
  • 18 separate output channels.
  • Central power for 16-camera systems.

Where to use it

It suits larger homes and compounds, apartment blocks, schools, churches, hotels, warehouses and offices where the cameras are cabled back to one cabinet. For a smaller system of up to eight cameras, the 9-channel 12 V 5 A power supply is the better fit.

Installation and setup

Install the unit indoors, in a dry and ventilated place close to the recorder. With the mains off, connect the AC input as marked on the unit, including the earth. Label each output with the camera it feeds, then connect the camera power cables observing polarity: positive to positive, negative to negative. If the unit has fuses or indicator lights on each channel, check them after power-up to confirm every camera is receiving power.

Plan cable sizes for distance. Cameras far from the cabinet lose voltage on thin cable, which often shows as night-time reboots when the infrared switches on. Kefa Solutions technicians can install complete CCTV systems if you would like the whole job done.

What you need with it

  • A 16-channel DVR or NVR and the cameras.
  • Power cable or combined video and power cable.
  • DC jacks or pigtails for each camera.
  • A mains isolator or fused spur for the cabinet.

Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock.

Frequently asked questions

Is 20A per channel or for the whole power supply?

The 20 A is the total for the whole unit, shared by all 18 outputs. If every channel is used, the average works out at a little over 1 A per camera. Add up the actual camera ratings, including night-time illumination, to make sure the total stays below 20 A with a margin.

Can I use it for fewer than 18 cameras?

Yes. Unused channels simply stay empty, and the spare outputs are useful when you add cameras later. If you only have four to eight cameras and do not plan to grow, a smaller 9-channel unit takes less space and suits the lower load better.

Why does one camera keep restarting at night?

At night the infrared lights switch on and the camera draws more current. On a long or thin power cable the voltage at the camera can then drop too low, and the camera reboots. Check the cable size and length, the connections at both ends, and that the total load on the supply is within 20 A.

KSh 6,000 In stock