

12V 20A Closed Switching Power Supply S-240-12
The S-240-12 is a closed-case switching power supply rated at 12 V DC and 20 A, about 240 W. It is meant for larger CCTV installations in Kenya, such as 16-camera systems, estates, schools and warehouses, where one well-sized central supply in the equipment cabinet is easier to manage than many plug adaptors.
- 12 V DC output at up to 20 A
- About 240 W total capacity
- Suits larger systems such as 16 cameras
- Closed casing with screw terminals
- Pickup from 3 Nairobi branches
- Nairobi delivery from KSh 200 (KSh 50/km)
- Countrywide courier in 1–3 working days
- Pay by M-Pesa, cash or bank transfer
Overview
The S-240-12 is a 12v 20a power supply in a closed casing, built to feed a large number of 12 V devices from a single point. It is the step up from the 10 A S-120-12, for jobs where the cameras, their night illumination and any other 12 V equipment add up to more than a 10 A unit can comfortably carry.
Who it suits
Twenty amps gives room for a sizeable system. Typical examples are a 16-camera installation around a compound, a school or church with cameras on several buildings, a warehouse or yard, or an apartment block where all cameras are powered from the ground-floor cabinet. Count every device: if you have eight cameras now and plan to add eight more next year, buying the 20 A supply once avoids replacing a smaller one later.
- 12 V DC output, up to 20 A.
- About 240 W in total, the meaning of the 240 in S-240-12.
- Closed casing with screw terminals.
- Central supply for larger CCTV and 12 V systems.
Planning the load
Take the current rating of each camera from its label or datasheet, using the figure with infrared or white light on, and add them up. Keep the total around three-quarters of 20 A so the supply is not running at its limit every night. Split the output into several fused circuits, for example one per side of the building, so a fault on one cable run only affects that group of cameras.
Installation and setup
A 240 W supply produces noticeable heat when loaded. Mount it in a dry, ventilated cabinet with space around it, not pressed against other equipment, and never outdoors. With the mains switched off, connect live, neutral and earth to the input, and run the 12 V output to a fused distribution board. If the unit has a 110/220 V selector, confirm it is on 220 V before connecting to Kenyan mains.
The higher the current, the more voltage is lost in thin cable. For a 20 A system, use properly sized power cable from the supply to the distribution point, and avoid feeding far-away cameras through long lengths of thin wire. Kefa Solutions technicians can install larger CCTV systems.
What you need with it
- A fused distribution board or CCTV power box.
- Power cable sized for the current and distance.
- A cabinet with ventilation, and an isolator on the mains side.
Pick it up at the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or order delivery.
Frequently asked questions
Is a 20A power supply too big for a small CCTV system?
A larger supply only delivers the current the cameras actually draw, so it will not harm a small system. The reasons to choose a smaller unit are size, heat and cost. If you expect to add cameras later, a 20 A supply gives room to grow without replacing it.
How should I split 20A between cameras?
Run the output to a fused distribution board and create several circuits, each with its own fuse sized for that group of cameras. That way a short in one cable only cuts power to that group. A CCTV power box with a fuse per channel does the same job in one enclosure.
Why do my far cameras flicker at night when the supply is 20A?
Usually the cable, not the supply. At night the infrared lights switch on and the cameras draw more current, so voltage drop on long, thin power cable increases and distant cameras may restart. Use thicker power cable, shorten the run, or power distant cameras from a closer supply.
Can I use it for 12V LED lighting as well?
Yes, any 12 V DC load can be powered as long as the total current of all devices stays within 20 A with some margin. Many installers prefer a separate supply for lighting so that a lighting fault does not affect the cameras.