Model S-120-12 SKU KCS-PSU-S120-12-10A

12V 10A Closed Switching Power Supply S-120-12

KSh 2,000
In stock — pick up today in Nairobi CBD

The S-120-12 is a closed-case switching power supply that delivers 12 V DC at up to 10 A (about 120 W). It suits installers in Kenya who want one central supply for a mid-sized CCTV system of several cameras, LED lighting or other 12 V equipment, instead of a separate adaptor at every camera.

  • 12 V DC output at up to 10 A
  • About 120 W total capacity
  • Closed casing with screw terminal connections
  • Central supply for a mid-sized CCTV system
  • Pickup from 3 Nairobi branches
  • Nairobi delivery from KSh 200 (KSh 50/km)
  • Countrywide courier in 1–3 working days
  • Pay by M-Pesa, cash or bank transfer

Overview

The S-120-12 is a 12v 10a power supply of the closed-case switching type: mains goes in on one side of a screw terminal strip and 12 V DC comes out on the other. With 10 A available, it is a sensible central supply for a mid-sized CCTV job where running a plug adaptor to every camera would be untidy and harder to maintain.

What 10 A means in practice

At 12 V, 10 A works out at about 120 W, which is what the 120 in the model code refers to. To size a system, read the current rating on each camera's label or datasheet and add them together. As an example, eight cameras rated at 0.5 A each draw 4 A, leaving plenty of headroom on a 10 A supply. Cameras with infrared or white-light illumination draw more at night than during the day, so always size for the night-time figure and keep around a quarter of the capacity spare.

  • 12 V DC output, up to 10 A.
  • About 120 W in total.
  • Closed casing with screw terminals for input and output.
  • Model code S-120-12.

Where to use it

A 10 A unit sits between the small 5 A supplies used for three or four cameras and the 20 A and 30 A units used on large sites. It is a good fit for a home with cameras around the compound, a shop or small office, or a block of flats where the recorder and power sit in one cabinet. It can also run 12 V LED strip lighting or other 12 V equipment, as long as the total current stays within 10 A.

Installation and setup

Mount the supply in a dry, ventilated place such as a CCTV cabinet, never outdoors where rain or dust can enter. Switch off the mains, connect live, neutral and earth to the input terminals, then take the positive and negative outputs to a distribution board or fused terminal block. Fusing each camera circuit separately means one shorted cable does not take every camera down. If your unit has a 110/220 V selector switch, check that it is set for 220 V before you connect it to Kenyan mains.

Voltage drops along long, thin cable, so on long runs use thicker power cable or place the supply closer to the cameras. Kefa Solutions technicians can install complete CCTV systems if you prefer the whole job done for you.

What you need with it

  • Power cable or combined video and power cable to each camera.
  • DC power jacks or pigtails for the camera ends.
  • A cabinet or enclosure, plus a fused spur or isolator on the mains side.

Collect from the Kefa CCTV Shop on Moi Avenue, Nairobi CBD, or order delivery within Nairobi or by courier across Kenya.

Frequently asked questions

How many CCTV cameras can a 12V 10A power supply run?

Add up the current rating of each camera, using the figure with night illumination switched on, and keep the total well under 10 A. Many cameras draw well under 1 A each, so a 10 A supply often handles a typical home or shop system, but check the labels on your cameras before deciding.

Can I put this power supply outside?

No. A closed switching supply is built to sit indoors or inside a cabinet. It has ventilation openings and screw terminals that must be kept away from rain, dust and insects. Mount it in a dry, ventilated cabinet and run only the low-voltage DC cable out to the cameras.

Do I need a separate fuse for each camera?

It is good practice. The supply feeds all cameras from one output, so a short circuit in one cable can trip the whole system. Taking the output to a fused distribution board, or using a CCTV power box with a fuse per channel, keeps the other cameras running while you trace the fault.

What is the difference between the S-120-12 and the S-240-12?

Both give 12 V DC. The S-120-12 is rated at 10 A, about 120 W, while the S-240-12 is rated at 20 A, about 240 W. Choose the larger unit when the total current of your cameras and other loads is close to or above 10 A.

KSh 2,000 In stock