Globe Insulating Tape
Globe insulating tape is an electrical tape on a roll for wrapping and insulating wire joints, bundling cables and marking wires. It is a basic item for electricians, CCTV installers and home repairs in Kenya. Collect it from the Kefa CCTV Shop in Nairobi CBD or add it to a delivery order.
- Electrical insulating tape on a roll
- Wraps low-voltage joints and bundles cables
- Useful for marking cable ends
- Toolbox basic for CCTV and electrical work
- Pickup from 3 Nairobi branches
- Nairobi delivery from KSh 200 (KSh 50/km)
- Countrywide courier in 1–3 working days
- Pay by M-Pesa, cash or bank transfer
Overview
Globe insulating tape is an adhesive tape sold on a roll for electrical and cabling work. Electricians and installers use it to cover wire joints, hold cables together and mark wires, and it is a handy item to keep in any toolbox in Nairobi and across Kenya.
Common uses
- Covering joints: wrap a joint in low-voltage wiring, such as a camera power lead, to keep bare copper covered.
- Bundling: hold several cables together neatly behind a TV, a recorder or a desk.
- Marking: mark cable ends so you know which camera, circuit or room each cable serves.
- Protection: add a layer over a scuffed cable jacket or a connector to keep dust out.
- Quick fixes: hold a cable in place while you fit clips or trunking.
For CCTV and low-voltage installations
On CCTV jobs, installers often join power cables at the camera end and wrap the joint before it goes into a junction box. Tape alone is not waterproof for long outdoor use, so outdoor joints should sit inside a junction box or a sealed connector, with tape as an extra layer. Marking each cable end with tape and a written label makes later fault-finding much faster.
How to apply it well
- Clean and dry the surface first; tape does not stick well to dusty or oily cable.
- Stretch the tape slightly as you wrap so it grips tightly.
- Overlap each turn by about half the tape width.
- Extend the wrap a little beyond the joint on both sides.
- Finish without pulling hard on the last turn, so the end does not lift.
Safety note
For mains power (240 V) wiring, use proper connectors, junction boxes and a qualified electrician. Insulating tape is not a replacement for correct terminations, and damaged mains cable should be replaced rather than repaired with tape. Switch off and isolate the supply before working on any circuit.
What to buy with it
Cable ties, cable clips, junction boxes, trunking and connectors for a tidy installation. Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock, such as roll length and colours. You can collect it from the shop in Nairobi CBD, get delivery within Nairobi (up to 45 km), or order by courier anywhere in Kenya in 1–3 working days.
Frequently asked questions
What is insulating tape used for?
It is used to cover and protect wire joints in low-voltage wiring, bundle cables together, mark cable ends and add a protective layer over scuffed cable jackets. On CCTV installations it is often used on camera power joints inside junction boxes and to label cables. It is a general-purpose tape for electrical and cabling work.
Can I use insulating tape on mains wiring?
Mains wiring should be joined with proper connectors inside an approved box and installed by a qualified electrician. Tape can add an extra layer, but it is not a replacement for correct terminations, and damaged mains cable should be replaced. Always switch off and isolate the supply before working on any circuit.
Is insulating tape waterproof outdoors?
Tape on its own should not be relied on to keep water out of an outdoor joint for long. Sun and rain can make the adhesive lift over time. Put outdoor joints inside a junction box or use sealed connectors, and use tape as an extra layer. Our team can suggest junction boxes that suit CCTV cameras.
What sizes and colours are available?
The roll length and colours of the Globe tape in stock can vary between deliveries. Ask our team at the Kefa CCTV Shop on Moi Avenue, Nairobi for the exact specification of the unit in stock before you order, especially if you need several colours for marking different circuits or cable runs.